Place your bets, how much power will it make?

Discussion in 'Mechanical - Engine, Gearbox, Exhaust etc' started by Steven878, Sep 22, 2013.

  1. Hi all,

    So the cars booked in to have the hybrid turbo remapped at RSTuning on Tuesday 24th at 10am, so thought i would start a thread and see what other people think it will make :smile:

    spec:
    CP forged low compression pistons
    Catcam steel conrods
    Catcam 421 high lift cams
    Ngk iridium spark plugs
    AET stage 2 hybrid turbo, with 20T cartridge and Billet compressor wheel
    Forge actuator with blue spring (spring starts to open at 1.1 bar)
    Forge blanking plate
    Forge dump valve with blue spring
    Forge boost pipe kit
    k-tec 3" exhaust
    3" decat pipe
    630cc injectors
    Itg/Samco induction kit (itg filter in wheel arch)
    Forge front mount intercooler
    Helix single mass flywheel

    Ideally i want 350bhp and 400lbft, but i think thats being a bit optimistic, but ill be happy with anything over 320bhp an 355lbft.

    Anyone want to guess what power the car will make?

    Steven
     
  2. 337 & 373 but will see on Tuesday.
     
  3. what time you going to be at rst mate?
     
  4. Christ with that spec you would hope to see anything from 330 upwards??? 335/380
     
  5. Leaving at 05.30 so between 09.30 and 10.00.
     
  6. I'd say 338bhp not sure on torque tbh.
     
  7. not sure what its going to make, as nobody else is using the same hybrid turbo and i also have a few other bits fitted that might help make more power.
    AET have done something to the turbine housing to try and make it flow better as well.
     
  8. ill be leaving at 5, so should be there for 9-10 depending on traffic.
    should be a good morning if everyone else makes it along :smile:
     
  9. I reckon about 198.5 and 205
     
  10. ^^^ haha, i guess there would be no point giving you a shot, if its going to make less than a standard car? Lol
     
  11. Gray

    Gray RSM Moderator

    Trying to swing my day around for being in Leeds, I am usually there on Wednesday. Will let you know tomorrow :smile:
     
  12. No probs mate, hopefully see you there tomorrow :smile:
     
  13. Good luck with the map/setup, feck the figures, with that super spec its gonna be immense driving experience..
     
  14. haha. At least you have your car at the moment....
     
  15. Cheers mate.
    I hope the car will be better to drive, as i find stage 2 power boring and slow now.
     
  16. still not got it back yet?
     
  17. Not yet. Been nearly a month now. I know they have been really busy though. I'm hopeful that I get it back this week
     
  18. 328 + 365, but hopefully you do get the figures you want :wink:
     
  19. My guess is 360/360.
     
  20. come on then....should be done by now!
     
  21. Sorry are with in a tardis because I am sure it is Monday 23rd not Tuesday the 24th!
     
  22. ^ lol.

    My guess is 335 & 350. Depends what they used on turbo.
     
  23. 340
     
  24. Lol i didnt even read the date! My bad!
     
  25. Sod's law that work has gone belly up so in not gonna get there now. I was looking forward to it.
     
  26. Markblack@MRS

    Markblack@MRS RSM Trader

    I made 310-310 without cams or a forged block
    I think you'll be close to 350-350
     
  27. I'm going for 355-355, and very, very jealous. :smile:
     
  28. Not long now! :smile:

    running the car on shell nitro, so all fuelled up, washed the car, checked the car over, etc, so all ready for my 5am start :smile:

    Shame the spec could be limited by the size of the turbine housing...
     
  29. Are you doing Cadwell on Thursday mate
     
  30. Cant make it mate.
    I was looking forward to putting names to faces and having a chat with folk face to face, as i think alot of stuff gets taken wrongly on forums, but the car gets mapped a day early and i haven't put holidays in at work to stay in a hotel for a couple of nights. :worried:
     
  31. no probs.
    let me know if your if your up my way anytime in the future and ill try and nip over :smile:
     
  32. Gray

    Gray RSM Moderator

    Couldn't swap my day around, sat at home writing up reports and a feasibility study.. :worried: GL mate!
     
  33. Flat!!!
     
  34. ?????
     
  35. time for a big turbo! lol.

    anyone want to buy a hybrid turbo setup????
     
  36. Bad news mate?
     
  37. What did it make Steven?
     
  38. Gray

    Gray RSM Moderator

    :worried: Doesn't sound good.
     
  39. Oh dear :worried: joes car is for sale Steve maybe you could swap some parts??
     
  40. car eventuall made 315bhp and 330lbft, but thats at 7300rpm.

    the cams are not matched to my turbo and have killed the performance. lol

    car still pulls alot better and feels so much smoother, but time to start saving for a big turbo kit.
     

  • Share This Page